Choose a product group and find the instruction you need.
SILAFIX FS-50, SILAFIX FS-75, SILAFIX FS-100, SilaFix Universal
Dots · strips · zigzag
The substrate must be clean, dry and sound: moisture up to 8 %, free of dust, grease and flaking paint. Prime loose and highly absorbent surfaces. Work at +15 °C or above and 40–60 % air humidity — the same conditions apply for the next 24 hours while the adhesive cures.
Cut the cartridge nozzle at an angle and apply the adhesive to the part in dots, strips or a zigzag: a 6 mm bead covers 14 metres. Place the part within 10 minutes and press for 4–5 seconds — after that it holds on its own. Clear FS-75 differs: let the adhesive dry for 5–6 minutes before pressing. Support large and heavy parts while the adhesive cures.
Full strength after 24 hours; the joint can then be sanded and painted. Fresh excess and tools wash off with water; dried adhesive is removed mechanically. The joint must not be in permanent contact with water. Store the cartridge at +5 to +20 °C with the nozzle tightly closed.
SILAFIX FS-150, SILAFIX FS-300
The substrate must be clean and sound; it may be damp, as the formulation bonds damp materials. Reinforce weak mineral substrates with a primer. PTFE, polyethylene and polypropylene are not suitable. Temperature during application and for the next 24 hours not below −20 °C, air humidity at least 40 %.
Apply the adhesive to the part in strips or dots; FS-300 is thicker than FS-150 and takes more effort on the gun. Place the part and press for 4–5 seconds — after that it holds on its own. Reposition within 30 minutes. Support large parts until fully cured.
Full cure after 24 hours; the joint can then be sanded and painted. Clean tools with white spirit right after work; dried residue can only be removed mechanically. The cured joint works from −40 to +120 °C.
SILAFIX FS-200 ULTRA: 290 ml cartridge and 80 ml tube. The cartridge needs a caulking gun; the tube is squeezed by hand.
Clean, degrease and dry both surfaces. Recommended bonding temperature: +15 to +30 °C. Check material compatibility.
Apply in zigzags, dots or a grid. Immediately join the parts, slide them slightly against one another, then separate them.
Wait 30 seconds to 1.5 minutes, rejoin the parts and press firmly. Initial grab takes 1–10 minutes; full cure takes 48 hours. Temporarily support heavy parts.
Not suitable for polyethylene, polypropylene, expanded polystyrene or flexible polyurethane foam. For mirrors, choose an adhesive compatible with their protective backing.
Contains solvent. Flammable. Work with ventilation, away from flames, sparks and heaters. Do not smoke. Wear gloves and keep out of reach of children. Follow the safety instructions on the specific packaging label.
DECOR ADHESIVE, ADHESIVE FILLER, ADHESIVE FILLER
The substrate must be clean, dry (moisture up to 8 %) and sound; prime loose and weak surfaces. Interior use only. Temperature during application and for the next 24 hours not below +12 °C for the decor adhesive and not below +15 °C for the adhesive filler.
Apply the adhesive to the part in a strip or dots; with the adhesive filler, fill joints and gaps with the same formulation and smooth with a spatula. Place the part within 10 minutes and press for 4–5 seconds. Support large parts while the adhesive cures. The formulation is solvent-free and does not attack foam.
After 24 hours the joint is sanded flush and painted together with the trim. Fresh excess and tools wash off with water. Store at +5 to +20 °C.
Acrylic sealant
The surface must be dry, sound and clean. Degrease glass and metal, prime highly porous substrates. Application temperature +12 to +30 °C.
Cut the nozzle to the joint size and apply the sealant as a continuous bead into the gap or joint. One cartridge covers 14–15 metres of a 5 mm joint.
Smooth the joint with a spatula and remove excess with a damp cloth before it dries. After curing the joint is elastic, water-resistant and paintable. Store the cartridge at +5 to +30 °C.
